sam firke dot com

Rare blog, rattlin’ blog

Category: How-to

  • , ,

    Watch repair: metal spring bar tore a channel in a Casio G-Shock end piece

    For Hanukkah 2008, I received a new watch from my wife. (I don’t remember the watch before that). It was particularly magical in my job as a high school teacher. After the first bell of the day rang, it was 4 minutes to the start of school, then 46 minutes per period alternating with a 4-minute passing period.

    The watch had a auto-repeating countdown timer that I set for 50 minutes and would synchronize with the day’s first bell. At any point during the day I could look down and see precisely how many seconds were left in a class or passing period. I could walk the hallways and announce “27 seconds!” or count down “5-4-3-2-1” and then the bell would ring, with me the only person in the school who had that level of precision.

    After years of daily wear and companionship, I received a smartwatch as a gift and stopped wearing the digital watch. I went from the Fitbit to a Basis and then a Garmin. At one point I realized I’d fallen into a consumerism trap and sought to go back. The notifications were disruptive and the data I was generating was useless to me but creepy in the hands of Big Tech. I tried to go back to the Casio, but it had a problem. (Remember the torn-out spring bar in the page title? This post is about the torn-out spring bar).

    Each strap is attached to the end piece / bezel by a spring bar. In the course of replacing a broken band and with wear and tear over time, the spring bar on one strap carved a channel from the hole it sits in. With slight force, the strap would pull the pin out through the channel and detach from the bezel. (If this post wasn’t an afterthought I’d have a “before” picture). This person appears to have the same problem, though they too did not post a picture.

    (more…)
    10 comments on Watch repair: metal spring bar tore a channel in a Casio G-Shock end piece
  • ,

    SD card not recognized in Ubuntu after formatting with GParted? Label it

    I formatted an SD card for use in a Raspberry Pi, in fat32 format using the GParted and following the steps in this post.

    But then Ubuntu didn’t recognize it, so I couldn’t put the NOOBS files on it. I went around in circles before giving the SD card a label, a step described as “if you wish” in that post. Voila! My SD card was immediately recognized.

    That’s all. Label the volume. Maybe this brief post helps someone searching the internet, but if nothing else I hope writing this makes me less likely to fall in this same trap again.

    No comments on SD card not recognized in Ubuntu after formatting with GParted? Label it
  • ,

    Things I’ve carried on a cargo bike

    I wrote about how the cargo bike changed my life. The #1 game changer is how mundane car errands become joyful adventures.  Whenever I can, I haul things by bike, and it’s become a game to see what new objects I can haul.

    Here are some favorites.  Photos 2016-2022.

    People

    Babies & Toddlers

    Babies love the Yepp seat.  They start off awake:

    look!  Sunglasses a must if riding an e-bike

    Then quickly doze off (don’t worry, he had his helmet on during the ride):

    (more…)
    2 comments on Things I’ve carried on a cargo bike
  • , ,

    Installing a top of stairs baby gate without drilling into wood trim or banister post

    The challenge: in an old house with nice woodwork, mount a baby gate at the top of the stairs such that it’s secure – without damaging the wood.

    baby gate at top of stairs
    The final product

    This was a fun project.  Got some ideas from YouTube videos (a learning format I usually dislike) and improvised a little.  This is built from scrap parts I had on hand, plus a baby gate I had installed at our previous home.

    The uneven surfaces presented by the trim on both sides pose the creative challenge.

    (more…)

    4 comments on Installing a top of stairs baby gate without drilling into wood trim or banister post
  • , ,

    What I care about vs. what I write about

    I’m disappointed with the misalignment between what’s important to me and what I write about here.  Here, I acknowledge and explore that.

    What I care about: meaningful, exciting, or useful ideas

    I have a list of substantial, interesting topics I’ve meant to write about.  Some are still relevant, others have drifted behind me as missed opportunities (e.g., I meant to discuss the August 2018 Ann Arbor Democratic primary elections).  Some are years old, others freshly sparked from recently conversations.

    Some of these topics are explored in abandoned drafts.  Others manifest on paper as just a single bullet point, albeit with hours of associated reflection and many references ready to go in my head.

    These more meaningful topics demand focus and time, which I have in only limited supply.  Such posts are also probably better when well-researched, which requires more time – though I’m growing suspicious that the burden of assembling links may not be worth it if it paralyzes me.  And I question whether it’s my place to write on them. Is my opinion valid? Do I know what I’m talking about?

    What I then write about: trivial, dull matters.

    Meanwhile, as these ideas languish, look at some of the blog posts I did manage to write in 2018.  I ranted against the TrailKeg, a thneed.  I wondered if old yard sign frames could be welded into a Papasan chair.  I wrote a how-to based on what I learned when configuring a specific model of solar panel monitoring gateway.

    (more…)

    No comments on What I care about vs. what I write about
  • ,

    Configuring Enphase Envoy for wifi without ethernet cord

    This is a how-to for connecting your Enphase Envoy (the oval one with the LCD screen) to connect to a home Wi-Fi network, without using an ethernet cable or the Enphase Installer Toolkit app.

    Enphase’s how-to guides give you about 80% of the information you need to do this, below are notes on things I figured out to fill in the other 20%.  Their guidance is geared toward installers, while this post is for homeowners who want to connect their Envoy to the home Wi-Fi network and don’t have a WPS button on their router or need to use another option.

    (more…)

    No comments on Configuring Enphase Envoy for wifi without ethernet cord